Category 5 cable
Unshielded twisted pair communications cable
- 4 min read
- 5 chapters
Related on Lably
Through Computer network, Ethernet over twisted pair and Telephone
This cable is commonly connected using punch-down blocks and modular connectors. Most Category 5 cables are unshielded, relying on the balanced line twisted pair design and differential signaling for noise suppression.
Standards
Category 5 is currently defined in ISO/IEC 11801, IEC 61156 and EN 50173, though it was originally defined in ANSI/TIA/EIA-568-A (with clarification in TSB-95). These documents specify performance characteristics and test requirements for frequencies up to 100 MHz.
The cable is available in both stranded and solid conductor forms. The stranded form is more flexible and withstands more bending without breaking. Patch cables are stranded. Permanent wiring used in structured cabling is solid. The category and type of cable can be identified by the printing on the jacket.
The Category 5 specification requires conductors to be pure copper. There has been a rise in counterfeit cables, especially of the copper-clad aluminum (CCA) variety. This has exposed the manufacturers and installers of such fake cable to legal liabilities.
Sign in to keep reading
4 more chapters are free with a Lably account.
Variants and comparisons
The Category 5e specification improves upon the Category 5 specification by further mitigating crosstalk. The bandwidth (100 MHz) and physical construction are the same between the two, and most Cat 5 cables actually happen to meet Cat 5e specifications even though they are not certified as such. Category 5 was deprecated in 2001 and superseded by the Category 5e specification.
The Category 6 specification improves upon the Category 5e specification by extending frequency response and further reducing crosstalk. The improved performance of Cat 6 provides 250 MHz bandwidth. Category 6A cable provides 500 MHz bandwidth. Both variants are backward compatible with Category 5 and 5e cables.
Termination
Cable types, connector types and cabling topologies are defined by ANSI/TIA-568. Category 5 cable is nearly always terminated with 8P8C modular connectors (often referred to incorrectly as RJ45 connectors). The cable is terminated in either the T568A scheme or the T568B scheme. The two schemes work equally well and may be mixed in an installation so long as the same scheme is used on both ends of each cable.
Applications
Category 5 cable is used in structured cabling for computer networks such as Ethernet over twisted pair. The cable standard prescribes performance parameters for frequencies up to 100 MHz and is suitable for 10BASE-T, 100BASE-TX (Fast Ethernet), 1000BASE-T (Gigabit Ethernet), 2.5GBASE-T and 10GBASE-T. 10BASE-T and 100BASE-TX Ethernet connections require two wire pairs. 1000BASE-T and faster Ethernet connections require four wire pairs. Through the use of power over Ethernet (PoE), power can be carried over the cable in addition to Ethernet data.
Cat 5 is also used to carry other signals such as telephony and video. In some cases, multiple signals can be carried on a single cable; Cat 5 can carry two conventional telephone lines as well as 100BASE-TX in a single cable. The USOC/RJ-61 wiring standard may be used in multi-line telephone connections. Various schemes exist for transporting both analog and digital video over the cable. HDBaseT (10.2 Gbit/s) is one such scheme.
Characteristics
The use of balanced lines helps preserve a high signal-to-noise ratio despite interference from both external sources and crosstalk from other pairs.
Insulation
Outer insulation is typically polyvinyl chloride (PVC) or low smoke zero halogen (LS0H).
Bending radius
Most Category 5 cables can be bent at any radius exceeding approximately four times the outside diameter of the cable.
Maximum cable segment length
The maximum length for a cable segment is 100 meters (330 ft) per TIA/EIA 568-5-A. If longer runs are required, the use of active hardware such as a repeater or switch is necessary. The specifications for 10BASE-T networking specify a 100-meter length between active devices. This allows for 90 meters of solid-core permanent wiring, two connectors and two stranded patch cables of 5 meters, one at each end.
Conductors
Since 1995, solid-conductor unshielded twisted pair (UTP) cables for backbone cabling have been required to be no thicker than 22 American Wire Gauge (AWG) and no thinner than 24 AWG, or 26 AWG for shorter-distance cabling. This standard has been retained with the 2009 revision of ANSI TIA/EIA 568.
Although cable assemblies containing four pairs are common, Category 5 is not limited to four pairs. Backbone applications involve using up to 100 pairs.
Individual twist lengths
The distance per twist is commonly referred to as pitch. Each of the four pairs in a Cat 5 cable has a differing pitch to minimize crosstalk between the pairs. The pitch of the twisted pairs is not specified in the standard.
Environmental ratings
Some cables are UV-rated or UV-stable meaning they can be exposed to outdoor UV radiation without significant degradation.
Plenum-rated cables are slower to burn and produce less smoke than cables using a mantle of materials like PVC. Plenum-rated cables may be installed in plenum spaces where PVC is not allowed.
Shielded cables (FTP or STP) are useful for environments where proximity to RF equipment may introduce electromagnetic interference, and can also be used where eavesdropping likelihood should be minimized.