Clamper (electronics)

Types

Clamp circuits are categorised by their operation: negative or positive, and biased or unbiased. A positive clamp circuit (negative peak clamper) outputs a purely positive waveform from an input signal; it offsets the input signal so that all of the waveform is greater than 0 V. A negative clamp is the opposite of this—this clamp outputs a purely negative waveform from an input signal. A bias voltage between the diode and ground offsets the output voltage by that amount.

For example, an input signal of peak value 5 V (V_INpeak = 5 V) is applied to a positive clamp with a bias of 3 V (V_BIAS = 3 V), the peak output voltage will be:

V_OUTpeak = 2 × V_INpeak + V_BIAS

V_OUTpeak = 2 × 5 V + 3 V

V_OUTpeak = 13 V

(The peak to peak excursion remains at 10 V.)

Positive unbiased

In the negative cycle of the input AC signal, the diode is forward biased and conducts, charging the capacitor to the peak negative value of V_IN. During the positive cycle, the diode is reverse biased and thus does not conduct. The output voltage is therefore equal to the voltage stored in the capacitor plus the input voltage, so V_OUT = V_IN + V_INpeak. This is also called a Villard circuit.

Negative unbiased

A negative unbiased clamp is the opposite of the equivalent positive clamp. In the positive cycle of the input AC signal, the diode is forward biased and conducts, charging the capacitor to the peak positive value of V_IN. During the negative cycle, the diode is reverse biased and thus does not conduct. The output voltage is therefore equal to the voltage stored in the capacitor plus the input voltage again, so V_OUT = V_IN − V_INpeak.

Positive biased

A positive biased voltage clamp is identical to an equivalent unbiased clamp but with the output voltage offset by the bias amount V_BIAS. Thus, V_OUT = V_IN + (V_INpeak + V_BIAS).

Negative biased

A negative biased voltage clamp is likewise identical to an equivalent unbiased clamp but with the output voltage offset in the negative direction by the bias amount V_BIAS. Thus, V_OUT = V_IN − (V_INpeak + V_BIAS).

Op-amp circuit

The figure shows an op-amp-based clamp circuit with a non-zero reference clamping voltage. The advantage here is that the clamping level is at precisely the reference voltage. There is no need to take into account the forward voltage drop of the diode (which is necessary in the preceding simple circuits as this adds to the reference voltage). The effect of the diode voltage drop on the circuit output will be divided down by the gain of the amplifier, resulting in an insignificant error. The circuit also has a great improvement in linearity at small input signals in comparison to the simple diode circuit and is largely unaffected by changes in the load.

Clamping for input protection

Clamping can be used to adapt an input signal to a device that cannot make use of or may be damaged by the signal range of the original input.

Principles of operation

During the first negative phase of the AC input voltage, the capacitor in a positive clamper circuit charges rapidly. As V_in becomes positive, the capacitor serves as a voltage doubler; since it has stored the equivalent of V_in during the negative cycle, it provides nearly that voltage during the positive cycle. This essentially doubles the voltage seen by the load. As V_in becomes negative, the capacitor acts as a battery of the same voltage of V_in. The voltage source and the capacitor counteract each other, resulting in a net voltage of zero as seen by the load.

Loading

For passive type clampers with a capacitor, followed by a diode in parallel with the load, the load can significantly affect performance. The magnitude of R and C are chosen so that the time constant, ${\displaystyle \tau =RC}$, is large enough to ensure that the voltage across the capacitor does not discharge significantly during the diode's non-conducting interval. A load resistance that is too low (heavy load) will partially discharge the capacitor and cause the waveform peaks to drift off the intended clamp voltage. This effect is greatest at low frequencies. At a higher frequency, there is less time between cycles for the capacitor to discharge.

The capacitor cannot be made arbitrarily large to overcome load discharge. During the conducting interval, the capacitor must be recharged. The time taken to do this is governed by a different time constant, this time set by the capacitance and the internal impedance of the driving circuit. Since the peak voltage is reached in one quarter cycle and then starts to fall again, the capacitor must be recharged in a quarter cycle. This requirement calls for a low value of capacitance.

The two conflicting requirements for capacitance value may be irreconcilable in applications with a high driving impedance and low load impedance. In such cases, an active circuit must be used such as the op-amp circuit described above.

Biased versus non-biased

By using a voltage source and resistor, the clamper can be biased to bind the output voltage to a different value. The voltage supplied to the potentiometer will be equal to the offset from zero (assuming an ideal diode) in the case of either a positive or negative clamper (the clamper type will determine the direction of the offset). If a negative voltage is supplied to either positive or negative, the waveform will cross the x-axis and be bound to a value of this magnitude on the opposite side. Zener diodes can also be used in place of a voltage source and potentiometer, hence setting the offset at the Zener voltage.

Examples

Clamping circuits were common in analog television receivers. These sets have a DC restorer circuit, which returns the voltage of the video signal during the "back porch" of the line blanking (retrace) period to 0 V. Low-frequency interference, especially power line hum, induced onto the signal spoils the rendering of the image and, in extreme, cases causes the set to lose synchronization. This interference can be effectively removed via this method.