Attenuation

Ultrasound

One area of research in which attenuation plays a prominent role is in ultrasound physics. Attenuation in ultrasound is the reduction in amplitude of the ultrasound beam as a function of distance through the imaging medium. Accounting for attenuation effects in ultrasound is important because a reduced signal amplitude can affect the quality of the image produced. By knowing the attenuation that an ultrasound beam experiences traveling through a medium, one can adjust the input signal amplitude to compensate for any loss of energy at the desired imaging depth.

• Ultrasound attenuation measurement in heterogeneous systems, like emulsions or colloids, yields information on particle size distribution. There is an ISO standard on this technique.
• Ultrasound attenuation can be used for extensional rheology measurement. There are acoustic rheometers that employ Stokes' law for measuring extensional viscosity and volume viscosity.

Wave equations which take acoustic attenuation into account can be written on a fractional derivative form.

In homogeneous media, the main physical properties contributing to sound attenuation are viscosity and thermal conductivity.

Attenuation coefficient

Attenuation coefficients are used to quantify different media according to how strongly the transmitted ultrasound amplitude decreases as a function of frequency. The attenuation coefficient (${\displaystyle \alpha }$) can be used to determine total attenuation in dB in the medium using the following formula:

${\displaystyle \text{Attenuation}=\alpha \left[\frac{\text{dB}}{\text{MHz}\cdot \text{cm}}\right]\cdot \ell [\text{cm}]\cdot \text{f}[\text{MHz}]}$

Attenuation is linearly dependent on the medium length and attenuation coefficient, as well as – approximately – the frequency of the incident ultrasound beam for biological tissue (while for simpler media, such as air, the relationship is quadratic). Attenuation coefficients vary widely for different media. In biomedical ultrasound imaging however, biological materials and water are the most commonly used media. The attenuation coefficients of common biological materials at a frequency of 1 MHz are listed below:

There are two general ways of acoustic energy losses: absorption and scattering. Ultrasound propagation through homogeneous media is associated only with absorption and can be characterized with absorption coefficient only. Propagation through heterogeneous media requires taking into account scattering.

Light attenuation in water

Shortwave radiation emitted from the Sun have wavelengths in the visible spectrum of light that range from 360 nm (violet) to 750 nm (red). When the Sun's radiation reaches the sea surface, the shortwave radiation is attenuated by the water, and the intensity of light decreases exponentially with water depth. The intensity of light at depth can be calculated using the Beer-Lambert Law.

In clear mid-ocean waters, visible light is absorbed most strongly at the longest wavelengths. Thus, red, orange, and yellow wavelengths are totally absorbed at shallower depths, while blue and violet wavelengths reach deeper in the water column. Because the blue and violet wavelengths are absorbed least compared to the other wavelengths, open-ocean waters appear deep blue to the eye.

Near the shore, coastal water contains more phytoplankton than the very clear mid-ocean waters. Chlorophyll-a pigments in the phytoplankton absorb light, and the plants themselves scatter light, making coastal waters less clear than mid-ocean waters. Chlorophyll-a absorbs light most strongly in the shortest wavelengths (blue and violet) of the visible spectrum. In coastal waters where high concentrations of phytoplankton occur, the green wavelength reaches the deepest in the water column and the color of water appears blue-green or green.

Seismic

The energy with which an earthquake affects a location depends on the running distance. The attenuation in the signal of ground motion intensity plays an important role in the assessment of possible strong groundshaking. A seismic wave loses energy as it propagates through the earth (seismic attenuation). This phenomenon is tied into the dispersion of the seismic energy with the distance. There are two types of dissipated energy:

• geometric dispersion caused by distribution of the seismic energy to greater volumes
• dispersion as heat, also called intrinsic attenuation or anelastic attenuation.

In porous fluid—saturated sedimentary rocks such as sandstones, intrinsic attenuation of seismic waves is primarily caused by the wave-induced flow of the pore fluid relative to the solid frame.

Electromagnetic

Attenuation decreases the intensity of electromagnetic radiation due to absorption or scattering of photons. Attenuation does not include the decrease in intensity due to inverse-square law geometric spreading. Therefore, calculation of the total change in intensity involves both the inverse-square law and an estimation of attenuation over the path.

The primary causes of attenuation in matter are the photoelectric effect, Compton scattering, and, for photon energies of above 1.022 MeV, pair production.

Coaxial and general RF cables

The attenuation of RF cables is defined by:

${\displaystyle \text{Attenuation (dB/100m)}=10\times {\log }_{10}\left(\frac{P_1(W)}{P_2(W)}\right),}$

where ${\displaystyle P_1}$ is the input power into a 100 m long cable terminated with the nominal value of its characteristic impedance, and ${\displaystyle P_2}$ is the output power at the far end of this cable.

Attenuation in a coaxial cable is a function of the materials and the construction.

Radiography

The beam of X-ray is attenuated when photons are absorbed when the x-ray beam passes through the tissue. Interaction with matter varies between high energy photons and low energy photons. Photons travelling at higher energy are more capable of travelling through a tissue specimen as they have less chances of interacting with matter. This is mainly due to the photoelectric effect which states that "the probability of photoelectric absorption is approximately proportional to (Z/E)³, where Z is the atomic number of the tissue atom and E is the photon energy. In context of this, an increase in photon energy (E) will result in a rapid decrease in the interaction with matter.

In CT imaging, attenuation describes the density or darkness of the image.

Optics

Attenuation in fiber optics, also known as transmission loss, is the reduction in intensity of the light beam (or signal) with respect to distance travelled through a transmission medium. Attenuation coefficients in fiber optics usually use units of dB/km through the medium due to the relatively high quality of transparency of modern optical transmission. The medium is typically a fiber of silica glass that confines the incident light beam to the inside. Attenuation is an important factor limiting the transmission of a digital signal across large distances. Thus, much research has gone into both limiting the attenuation and maximizing the amplification of the optical signal. Empirical research has shown that attenuation in optical fiber is caused primarily by both scattering and absorption.

Attenuation in fiber optics can be quantified using the following equation:

${\displaystyle \text{Attenuation (dB)}=10\times {\log }_{10}\left(\frac{\text{Input intensity (W)}}{\text{Output intensity (W)}}\right)}$

Light scattering

The propagation of light through the core of an optical fiber is based on total internal reflection of the lightwave. Rough and irregular surfaces, even at the molecular level of the glass, can cause light rays to be reflected in many random directions. This type of reflection is referred to as "diffuse reflection", and it is typically characterized by wide variety of reflection angles. Most objects that can be seen with the naked eye are visible due to diffuse reflection. Another term commonly used for this type of reflection is "light scattering". Light scattering from the surfaces of objects is our primary mechanism of physical observation. Light scattering from many common surfaces can be modelled by reflectance.

Light scattering depends on the wavelength of the light being scattered. Thus, limits to spatial scales of visibility arise, depending on the frequency of the incident lightwave and the physical dimension (or spatial scale) of the scattering center, which is typically in the form of some specific microstructural feature. For example, since visible light has a wavelength scale on the order of one micrometer, scattering centers will have dimensions on a similar spatial scale.

Thus, attenuation results from the incoherent scattering of light at internal surfaces and interfaces. In (poly)crystalline materials such as metals and ceramics, in addition to pores, most of the internal surfaces or interfaces are in the form of grain boundaries that separate tiny regions of crystalline order. It has recently been shown that, when the size of the scattering center (or grain boundary) is reduced below the size of the wavelength of the light being scattered, the scattering no longer occurs to any significant extent. This phenomenon has given rise to the production of transparent ceramic materials.

Likewise, the scattering of light in optical quality glass fiber is caused by molecular-level irregularities (compositional fluctuations) in the glass structure. Indeed, one emerging school of thought is that a glass is simply the limiting case of a polycrystalline solid. Within this framework, "domains" exhibiting various degrees of short-range order become the building-blocks of both metals and alloys, as well as glasses and ceramics. Distributed both between and within these domains are microstructural defects that will provide the most ideal locations for the occurrence of light scattering. This same phenomenon is seen as one of the limiting factors in the transparency of IR missile domes.

UV-Vis-IR absorption

In addition to light scattering, attenuation or signal loss can also occur due to selective absorption of specific wavelengths, in a manner similar to that responsible for the appearance of color. Primary material considerations include both electrons and molecules as follows:

• At the electronic level, it depends on whether the electron orbitals are spaced (or "quantized") such that they can absorb a quantum of light (or photon) of a specific wavelength or frequency in the ultraviolet (UV) or visible ranges. This is what gives rise to color.
• At the atomic or molecular level, it depends on the frequencies of atomic or molecular vibrations or chemical bonds, how close-packed its atoms or molecules are, and whether or not the atoms or molecules exhibit long-range order. These factors will determine the capacity of the material transmitting longer wavelengths in the infrared (IR), far IR, radio and microwave ranges.

The selective absorption of infrared (IR) light by a particular material occurs because the selected frequency of the light wave matches the frequency (or an integral multiple of the frequency) at which the particles of that material vibrate. Since different atoms and molecules have different natural frequencies of vibration, they will selectively absorb different frequencies (or portions of the spectrum) of infrared (IR) light.

Applications

In optical fibers, attenuation is the rate at which the signal light decreases in intensity. For this reason, glass fiber (which has a low attenuation) is used for long-distance fiber optic cables; plastic fiber has a higher attenuation and, hence, shorter range. There also exist optical attenuators that decrease the signal in a fiber optic cable intentionally.

Attenuation of light is also important in physical oceanography. This same effect is an important consideration in weather radar, as raindrops absorb a part of the emitted beam that is more or less significant, depending on the wavelength used.

Due to the damaging effects of high-energy photons, it is necessary to know how much energy is deposited in tissue during diagnostic treatments involving such radiation. In addition, gamma radiation is used in cancer treatments where it is important to know how much energy will be deposited in healthy and in tumorous tissue.

In computer graphics attenuation defines the local or global influence of light sources and force fields.

Radio

Attenuation is an important consideration in the modern world of wireless telecommunications. Attenuation limits the range of radio signals and is affected by the materials a signal must travel through (e.g., air, wood, concrete, rain). See the article on path loss for more information on signal loss in wireless communication.