Rainwater harvesting

Technologies

Traditionally, stormwater management using detention basins served a single purpose. However, optimized real-time control lets this infrastructure double as a source of rainwater harvesting without compromising the existing detention capacity. This has been used in the EPA headquarters to evacuate stored water prior to storm events, thus reducing wet weather flow while ensuring water availability for later reuse. This has the benefit of increasing water quality released and decreasing the volume of water released during combined sewer overflow events.

Generally, check dams are constructed across the streams to enhance the percolation of surface water into the subsoil strata. The water percolation in the water-impounded area of the check dams can be enhanced artificially manyfold by loosening the subsoil strata by using ANFO explosives as used in open cast mining. Thus, local aquifers can be recharged quickly using the available surface water fully for use in the dry season.

System setup

Rainwater harvesting systems can range in complexity, from systems that can be installed with minimal skills, to automated systems that require advanced setup and installation. The basic rainwater harvesting system is more of a plumbing job than a technical job, as all the outlets from the building's terrace are connected through a pipe to an underground tank that stores water. There are common components that are installed in such systems, such as pre-filters (see e.g. vortex filter), drains/gutters, storage containers, and depending on whether the system is pressurized, also pumps, and treatment devices such as UV lights, chlorination devices and post-filtration equipment.

Systems are ideally sized to meet the water demand throughout the dry season since it must be big enough to support daily water consumption. Specifically, the rainfall capturing area such as a building roof must be large enough to maintain an adequate flow of water. The water storage tank size should be large enough to contain the captured water. For low-tech systems, many low-tech methods are used to capture rainwater: rooftop systems, surface water capture, and pumping the rainwater that has already soaked into the ground or captured in reservoirs and storing it in tanks (cisterns).

Rainwater harvesting by solar power panels

Good quality water resources near populated areas are becoming scarce and costly for consumers. In addition to solar and wind energy, rainwater is a major renewable resource for any land. Vast areas are being covered by solar PV panels every year in all parts of the world. Solar panels can also be used for harvesting most of the rainwater falling on them and drinking quality water, free from bacteria and suspended matter, can be generated by simple filtration and disinfection processes as rainwater is very low in salinity. Exploiting rainwater for value-added products like bottled drinking water makes solar PV power plants profitable even in high rainfall or cloudy areas by generating additional income. Recently, cost-effective rainwater collection in existing wells has been found highly effective in raising groundwater levels in India.

Other innovations

The Groasis Waterboxx is an example of low scale technology which aids in the planting of trees in arid areas. It harvests rainwater and dew.

The Global Rainwater Management Program is a water conservation initiative suggested by the UNCCD and the Global Water Partnership.

Advantages

Rainwater harvesting provides an independent water supply during regional water restrictions, and in developed countries, it is often used to supplement the main supply. It provides water when a drought occurs, can help mitigate flooding of low-lying areas, and reduces demand on wells which may enable groundwater levels to be sustained. Rainwater harvesting increases the availability of water during dry seasons by increasing the levels of dried borewells and wells. Surface water supply is readily available for various purposes thus reducing dependence on underground water. It improves the quality of ground by diluting salinity. It does not cause pollution and is environmentally friendly. It is cost-effective and easily affordable. It also helps in the availability of potable water, as rainwater is substantially free of salinity and other salts. Applications of rainwater harvesting in urban water system provides a substantial benefit for both water supply and wastewater subsystems by reducing the need for clean water in water distribution systems, less generated stormwater in sewer systems, and a reduction in stormwater runoff polluting freshwater bodies.

A large body of work has focused on the development of life cycle assessment and its costing methodologies to assess the level of environmental impacts and money that can be saved by implementing rainwater harvesting systems. Purified rainwater as a source of water supply can reduce the burden on public/municipal water supplies, while unpurified rainwater can be used for toilet flushing, and gardening. This decreases reliance on treated municipal water or groundwater, helping conserve limited freshwater resources, especially in areas with high demand or water shortages.

Independent water supply

Rainwater harvesting provides an independent water supply during water restrictions. In areas where clean water is costly, or difficult to come by, rainwater harvesting is a critical source of clean water. In developed countries, rainwater is often harvested to be used as a supplemental source of water rather than the main source, but the harvesting of rainwater can also decrease a household's water costs or overall usage levels. Rainwater is safe to drink if the consumers do additional treatments before drinking. Boiling water helps to kill germs. Adding another supplement to the system such as a first flush diverter is also a common procedure to avoid contaminants of the water.

Supplemental in drought

When drought occurs, rainwater harvested in past months can be used. If rain is scarce but also unpredictable, the use of a rainwater harvesting system can be critical to capturing the rain when it does fall. Many countries with arid environments, use rainwater harvesting as a cheap and reliable source of clean water. To enhance irrigation in arid environments, ridges of soil are constructed to trap and prevent rainwater from running downhills. Even in periods of low rainfall, enough water is collected for crops to grow. Water can be collected from roofs and tanks can be constructed to hold large quantities of rainwater.

In addition, rainwater harvesting decreases the demand for water from wells, enabling groundwater levels to be further sustained rather than depleted.

Life-cycle assessment

Life-cycle assessment is a methodology used to evaluate the environmental impacts of a system from cradle-to-grave of its lifetime. Devkota et al, developed such a methodology for rainwater harvesting, and found that the building design (e.g., dimensions) and function (e.g., educational, residential, etc.) play critical roles in the environmental performance of the system.

To address the functional parameters of rainwater harvesting systems, a new metric was developed – the demand to supply ratio (D/S) – identifying the ideal building design (supply) and function (demand) in regard to the environmental performance of rainwater harvesting for toilet flushing. With the idea that supply of rainwater not only saves the potable water but also saves the stormwater entering the combined sewer network (thereby requiring treatment), the savings in environmental emissions were higher if the buildings are connected to a combined sewer network compared to separate one.

Cost-effectiveness

Although standard RWH systems can provide a water source to developing regions facing poverty, the average cost for an RWH setup can be costly depending on the type of technology used. Governmental aid and NGOs can assist communities facing poverty by providing the materials and education necessary to develop and maintain RWH setups.

Some studies show that rainwater harvesting is a widely applicable solution for water scarcity and other multiple usages, owing to its cost-effectiveness and eco-friendliness. Constructing new substantial, centralized water supply systems, such as dams, is prone to damage local ecosystems, generates external social costs, and has limited usages, especially in developing countries or impoverished communities. On the other hand, installing rainwater harvesting systems is verified by a number of studies to provide local communities a sustainable water source, accompanied by other various benefits, including protection from flood and control of water runoff, even in poor regions. Rainwater harvesting systems that do not require major construction or periodic maintenance by a professional from outside the community are more friendly to the environment and more likely to benefit the local people for a longer period of time. Thus, rainwater harvesting systems that could be installed and maintained by local people have bigger chances to be accepted and used by more people.

The usage of in-situ technologies can reduce investment costs in rainwater harvesting. In-situ technologies for rainwater harvesting could be a feasible option for rural areas since less material is required to construct them. They can provide a reliable water source that can be utilized to expand agricultural outputs. Above-ground tanks can collect water for domestic use; however, such units can be unaffordable to people in poverty.

Limitations

Rainwater harvesting is a widely used method of storing rainwater in countries presenting with drought characteristics. Several pieces of research have derived and developed different criteria and techniques to select suitable sites for harvesting rainwater. Some research was identified and selected suitable sites for the potential erection of dams, as well as derived a model builder in ArcMap 10.4.1. The model combined several parameters, such as slope, runoff potential, land cover/use, stream order, soil quality, and hydrology to determine the suitability of the site for harvesting rainwater.

Harvested water from RWH systems can be minimal during below-average precipitation in arid urban regions such as the Middle East. RWH is useful for developing areas as it collects water for irrigation and domestic purposes. However, the gathered water should be adequately filtered to ensure safe drinking.

Quality of water

Rainwater may need to be analyzed properly, and used in a way appropriate to its safety. In the Gansu province, for example, solar water disinfection is used by boiling harvested rainwater in parabolic solar cookers before being used for drinking. These so-called "appropriate technology" methods provide low-cost disinfection options for treatment of stored rainwater for drinking.

While rainwater itself is a clean source of water, often better than groundwater or water from rivers or lakes, the process of collection and storage often leaves the water polluted and non-potable. Rainwater harvested from roofs can contain human, animal and bird feces, mosses and lichens, windblown dust, particulates from urban pollution, pesticides, and inorganic ions from the sea (Ca, Mg, Na, K, Cl, SO4), and dissolved gases (CO₂, NO_x, SO_x). High levels of pesticide have been found in rainwater in Europe with the highest concentrations occurring in the first rain immediately after a dry spell; the concentration of these and other contaminants are reduced significantly by diverting the initial flow of run-off water to waste. Improved water quality can also be obtained by using a floating draw-off mechanism (rather than from the base of the tank) and by using a series of tanks, withdraw from the last in series. Prefiltration is a common practice used in the industry to keep the system healthy and ensure that the water entering the tank is free of large sediments.

A concept of rainwater harvesting and cleaning it with solar energy for rural household drinking purposes has been developed by Nimbkar Agricultural Research Institute.

Conceptually, a water supply system should match the quality of water with the end-user. However, in most of the developed world, high-quality potable water is used for all end uses. This approach wastes money and energy and imposes unnecessary impacts on the environment. Supplying rainwater that has gone through preliminary filtration measures for non-potable water uses, such as toilet flushing, irrigation, and laundry, may be a significant part of a sustainable water management strategy.

Rainwater cisterns can also act as habitat for pathogen-bearing mosquitoes. As a result, care must be taken to ensure that female mosquitoes can not access the cistern to lay eggs. Larvae eating fish can also be added to the cistern, or it can be chemically treated.

Country examples

Canada

Rainwater harvesting is becoming a procedure that many Canadians are incorporating into their daily lives, although data does not give exact figures for implementation. Rainwater can be used for a number of purposes including stormwater reduction, irrigation, laundry and portable toilets. In addition to low costs, rainwater harvesting is useful for landscape irrigation. Many Canadians have started implementing rainwater harvesting systems for use in stormwater reduction, irrigation, laundry, and lavatory plumbing. Provincial and municipal legislation is in place for regulating the rights and uses for captured rainwater. Substantial reform to Canadian law since the mid-2000s has increased the use of this technology in agricultural, industrial, and residential use, but ambiguity remains amongst legislation in many provinces. Bylaws and local municipal codes often regulate rainwater harvesting.

Multiple organizations and companies have developed in Canada to provide education, technology, and installation for rainwater harvesting. These include the Canadian Association for Rainwater Management (CANARM), Canadian Mortgage and Housing Corporation (CMHC), and CleanFlo Water Technologies. CANARM is an association that prioritizes education, training and spreading awareness for those entering the rainwater harvesting industry.

India

In the early 21st century, India began heavily investing in rainwater harvesting infrastructure and policy as an urgent response to water scarcity. In 2001, Tamil Nadu became the first Indian state to make rainwater harvesting compulsory in every building to avoid groundwater depletion. In Rajasthan, rainwater harvesting has traditionally been practised by the people of the Thar Desert. Increase in rainwater harvesting efforts across the nation have revived ancient water harvesting systems in Rajasthan, such as the chauka system from the Jaipur district. Other large cities like Pune, Mumbai and Bangalore all have varying rules for mandatory rainwater harvesting, especially in new buildings. In 2002, the Municipal Corporation of Greater Mumbai required all new buildings over 1,000 square metres (11,000 sq ft) to have rainwater harvesting infrastructure. The law was expanded in 2007 to 300 square metres (3,200 sq ft). The goal was to ensure buildings had enough water to last them through non-monsoon seasons. The process included a catchment system, an initial flush, and extensive filtering. As of 2021, the Brihanmumbai Municipal Corporation (BMC) reported 3000 newly constructed or redeveloped buildings with rainwater harvesting infrastructure. However, many residents have complained that the stored water is contaminated, turning saline and brackish. Experts and residents argue that BMC authorities have done little to take implementation seriously, and the actual effectiveness of the rainwater harvesting mandate is unknown.

While rainwater harvesting in an urban context has gained traction in recent years, evidence points toward rainwater harvesting in rural India since ancient times.

United Kingdom

Rainwater harvesting in the United Kingdom is a practice of growing importance. Rainwater harvesting in the UK is both a traditional and a reviving technique for collecting water for domestic uses. The water is generally used for non-hygienic purposes like watering gardens, flushing toilets, and washing clothes. In commercial premises like supermarkets it is used for things like toilet flushing where larger tank systems can be used collecting between 1000 and 7500 litres of water. It is claimed that in the South East of England there is less water available per person than in many Mediterranean countries.

Rainwater is almost always collected strictly from the roof, then heavily filtered using either a filter attached to the down pipe, a fine basket filter or for more expensive systems like self-cleaning filters placed in an underground tank. UK homes using some form of rainwater harvesting system can reduce their mains water usage by 50% or more, although a 20%–30% saving is more common. At present (depending on the area in the UK) mains water delivery and equivalent waste water and sewerage processing costs about £2 per cubic metre. Reducing mains-water metered volumes also reduces the sewerage and sewage disposal costs in the same proportion, because water company billing assumes that all water taken into the house is discharged into the sewers.

United States

In the United States, until 2009 in Colorado, water rights laws almost completely restricted rainwater harvesting; a property owner who captured rainwater was deemed to be stealing it from those who have the rights to take water from the watershed. Now, residential good owners who meet certain criteria may obtain a permit to install a rooftop precipitation collection system (SB 09-080). Up to 10 large scale pilot studies may also be permitted (HB 09–1129). The main factor in persuading the Colorado Legislature to change the law was a 2007 study that found that in an average year, 97% of the precipitation that fell in Douglas County, in the southern suburbs of Denver, never reached a stream—it was used by plants or evaporated on the ground. Rainwater catchment is mandatory for new dwellings in Santa Fe, New Mexico. Texas offers a sales tax exemption on the purchase of rainwater harvesting equipment. Both Texas and Ohio allow the practice even for potable purposes. Oklahoma passed the Water for 2060 Act in 2012, to promote pilot projects for rainwater and graywater use among other water-saving techniques.

Other countries

• Uganda: Rainwater harvesting has been used in Uganda to promote household and community scale water security for many years. Regular maintenance is an ongoing challenge with existing installation and there are many examples of installations that have failed due to poor maintenance. Research has also shown that awareness of RWH and how to access necessary resources to implement RWH is variable across Ugandan society.
• Thailand has the largest fraction of the population in the rural area relying on rainwater harvesting (currently around 40%). Rainwater harvesting was promoted heavily by the government in the 1980s. In the 1990s, after government funding for the collection tanks ran out, the private sector stepped in and provided several million tanks to private households, many of which continue to be used. This is one of the largest examples of self-supply of water worldwide.
• In Bermuda, the law requires all new construction to include rainwater harvesting adequate for the residents.
• New Zealand has plentiful rainfall in the West and South, and rainwater harvesting is the normal practice in many rural areas, using roof water directed by spouting into covered, 1000 litre storage tanks, with the encouragement of most local councils.
• In Sri Lanka, rainwater harvesting has been a popular method of obtaining water for agriculture and for drinking purposes in rural homes. The legislation to promote rainwater harvesting was enacted through the Urban Development Authority (Amendment) Act, No. 36 of 2007. The Lanka Rainwater Harvesting Forum is leading Sri Lanka's initiative. The tank cascade system is an ancient irrigation system spanning the island of Sri Lanka.
• In Bolivia, rainwater harvesting projects have been introduced in rural and suburban schools to help address water scarcity and support school-based agriculture. In Cochabamba, initiatives led by local NGOs and community members have used rooftop collection systems to supply gardens that provide meals for students.

History

The construction and use of cisterns to store rainwater can be traced back to the Neolithic Age, when waterproof lime plaster cisterns were built in the floors of houses in village locations of the Levant, a large area in Southwest Asia, south of the Taurus Mountains, bounded by the Mediterranean Sea in the west, the Arabian Desert in the south, and Mesopotamia in the east. By the late 4000 BC, cisterns were essential elements of emerging water management techniques used in dry-land farming.

Many ancient cisterns have been discovered in some parts of Jerusalem and throughout what is today Israel/Palestine. At the site believed by some to be that of the biblical city of Ai (Khirbet et-Tell), a large cistern dating back to around 2500 BC was discovered that had a capacity of nearly 1,700 m³ (60,000 cu ft). It was carved out of a solid rock, lined with large stones, and sealed with clay to keep it from leaking.

The Greek island of Crete is also known for its use of large cisterns for rainwater collection and storage during the Minoan period from 2,600 BC–1,100 BC. Four large cisterns have been discovered at Myrtos-Pyrgos, Archanes, and Zakroeach. The cistern found at Myrtos-Pyrgos was found to have a capacity of more than 80 m³ (2,800 cu ft) and to date back to 1700 BC.

Around 300 BC, farming communities in Balochistan (now located in Pakistan, Afghanistan, and Iran), and Kutch, India, used rainwater harvesting for agriculture and many other uses. Rainwater harvesting was done by Chola kings as well. Rainwater from the Brihadeeswarar temple (located in Balaganapathy Nagar, Thanjavur, India) was collected in Shivaganga tank. During the later Chola period, the Vīrānam tank was built (1011 to 1037 AD) in the Cuddalore district of Tamil Nadu to store water for drinking and irrigation purposes. Vīrānam is a 16-km-long tank with a storage capacity of 1,465,000,000 cu ft (41,500,000 m³).

Rainwater harvesting was also common in the Roman Empire. While Roman aqueducts are well-known, Roman cisterns were also commonly used and their construction expanded with the Empire. For example, in Pompeii, rooftop water storage was common before the construction of the aqueduct in the 1st century BC. This history continued with the Byzantine Empire; for example, the Basilica Cistern in Istanbul.

Though little known, the town of Venice for centuries depended on rainwater harvesting. The lagoon surrounding Venice is brackish water, which is unsuitable for drinking. Venice's ancient inhabitants established a rainwater collection system based on man-made insulated collection wells. Water percolated down the specially designed stone flooring, and was filtered by a layer of sand, then collected at the bottom of the well. Later, as Venice acquired territories on the mainland, it started to import water by boat from local rivers. Still, the wells remained in use and were especially important in times of war when an enemy could block access to the mainland water.

Urban implementation

In urban areas, rainwater harvesting systems are integrated into building designs to reduce runoff and supplement water supply. Cities like Melbourne, Singapore and Hyderabad have adopted policies encouraging rainwater collection in residential and commercial buildings.