Throttle

Throttle body

In fuel injected engines, the throttle body is the part of the air intake system that controls the amount of air flowing into the engine, in response to driver accelerator pedal input in the main. The throttle body is usually located between the air filter box and the intake manifold, and it is usually attached to, or near, the mass airflow sensor. Often, an engine coolant line also runs through it in order for the engine to draw intake air at a certain temperature (the engine's current coolant temperature, which the ECU senses through the relevant sensor) and therefore with a known density.

The largest piece inside the throttle body is the throttle plate, which is a butterfly valve that regulates the airflow.

On many cars, the accelerator pedal motion is communicated via the throttle cable, which is mechanically connected to the throttle linkages, which, in turn, rotate the throttle plate. In cars with electronic throttle control (also known as "drive-by-wire"), an electric actuator controls the throttle linkages and the accelerator pedal connects not to the throttle body, but to a sensor, which outputs a signal proportional to the current pedal position and sends it to the ECU. The ECU then determines the throttle opening based on the accelerator pedal's position and inputs from other engine sensors such as the engine coolant temperature sensor.

When the driver presses on the accelerator pedal, the throttle plate rotates within the throttle body, opening the throttle passage to allow more air into the intake manifold, immediately drawn inside by its vacuum. Usually a mass airflow sensor measures this change and communicates it to the ECU. The ECU then increases the amount of fuel injected by the injectors in order to obtain the required air-fuel ratio. Often a throttle position sensor (TPS) is connected to the shaft of the throttle plate to provide the ECU with information on whether the throttle is in the idle position, wide-open throttle (WOT) position, or somewhere in between these extremes.

Throttle bodies may also contain valves and adjustments to control the minimum airflow during idle. Even in those units that are not "drive-by-wire", there will often be a small solenoid driven valve, the Idle Air Control Valve (IACV), that the ECU uses to control the amount of air that can bypass the main throttle opening to allow the engine to idle when the throttle is closed.

A throttle body is somewhat analogous to the carburetor in a non-injected engine, although it is important to remember that a throttle body is not the same thing as a throttle, and that carbureted engines have throttles as well. A throttle body simply supplies a convenient place to mount a throttle in the absence of a carburetor venturi. Carburetors are an older technology, which mechanically modulate the amount of air flow (with an internal throttle plate) and combine air and fuel together (venturi). Cars with fuel injection don't need a mechanical device to meter the fuel flow, since that duty is taken over by injectors in the intake pathways (for multipoint fuel injection systems) or cylinders (for direct injection systems) coupled with electronic sensors and computers which precisely calculate how long should a certain injector stay open and therefore how much fuel should be injected by each injection pulse. However, they do still need a throttle to control the airflow into the engine, together with a sensor that detects its current opening angle, so that the correct air/fuel ratio can be met at any RPM and engine load combination. The simplest way to do this is to simply remove the carburetor unit, and bolt a simple unit containing a throttle body and fuel injectors on instead. This is known as single-port injection, also known by different marketing names (such as "throttle-body injection" by General Motors and "central fuel injection" by Ford, among others), and it allows an older engine design to be converted from carburetor to fuel injection without significantly altering the intake manifold design. More complex later designs use intake manifolds, and even cylinder heads, specially designed for the inclusion of injectors.

Multiple throttle bodies

Most fuel injected cars have a single throttle, contained in a throttle body. Vehicles can sometimes employ more than one throttle body, connected by linkages to operate simultaneously, which improves throttle response and allows a straighter path for the airflow to the cylinder head, as well as for equal-distance intake runners of short length, difficult to achieve when all the runners have to travel to certain location to connect to a single throttle body, at the cost of greater complexity and packaging issues. At the extreme, higher-performance cars like the E92 BMW M3 and Ferraris, and high-performance motorcycles like the Yamaha R6, can use a separate throttle body for each cylinder, often called "individual throttle bodies" or ITBs. Although rare in production vehicles, these are common equipment on many racing cars and modified street vehicles. This practice harks back to the days when many high performance cars were given one, small, single-venturi carburettor for each cylinder or pair of cylinders (i.e. Weber, SU carburettors), each one with their own small throttle plate inside. In a carburettor, the smaller throttle opening also allowed for more precise and fast carburettor response, as well as better atomization of the fuel when running at low engine speeds.

Other engines

Steam locomotives normally have the throttle (North American English) or regulator (British English) in a characteristic steam dome at the top of the boiler (although not all boilers feature these). The additional height afforded by the dome helps to avoid any liquid (e.g. from bubbles on the surface of the boiler water) being drawn into the throttle valve, which could damage it, or lead to priming. The throttle is basically a poppet valve, or series of poppet valves which open in sequence to regulate the amount of steam admitted to the steam chests over the pistons. It is used in conjunction with the reversing lever to start, stop and to control the locomotive's power although, during steady-state running of most locomotives, it is preferable to leave the throttle wide open and to control the power by varying the steam cut-off point (which is done with the reversing lever), as this is more efficient. A steam locomotive throttle valve poses a difficult design challenge as it must be opened and closed using hand effort against the considerable pressure (typically 250 psi or 1,700 kPa) of boiler steam. One of the primary reasons for later multiple-sequential valves: it is far easier to open a small poppet valve against the pressure differential, and open the others once pressure begins to equalize than to open a single large valve, especially as steam pressures eventually exceeded 200 psi (1,400 kPa) or even 300 psi (2,100 kPa). Examples include the balanced "double beat" type used on Gresley A3 Pacifics.

Electric vehicle throttle is controlled with Hall-effect sensor.

Throttling of a rocket engine means varying the thrust level in-flight. This is not always a requirement; in fact, the thrust of a solid-fuel rocket is not controllable after ignition, and is instead pre-planned by varying the shape of the void down the center of the booster when the fuel is molded. However, liquid-propellant rockets can be throttled by means of valves which regulate the flow of fuel and oxidizer to the combustion chamber. Hybrid rocket engines, such as the one used in Space Ship One, use solid fuel with a liquid oxidizer, and therefore can be throttled. Throttling tends to be required more for powered landings, and launch into space using a single main stage (such as the Space Shuttle), than for launch with multistage rockets. They are also useful in situations where the airspeed of the vehicle must be limited due to aerodynamic stress in the denser atmosphere at lower levels (e.g. the Space Shuttle). Rockets characteristically become lighter the longer they burn, with the changing ratio of thrust:weight resulting in increasing acceleration, so engines are often throttled (or switched off) to limit acceleration forces towards the end of a stage's burn time if it is carrying sensitive cargo (e.g. humans).

In a jet engine, thrust is controlled by changing the amount of fuel flowing into the combustion chamber, similar to a diesel engine.

Lifespan of the throttle in cars

The lifespan of the throttle is not set since it highly depends on the driving style and specific vehicle. The throttle tends to be quite dirty after 100-150 thousand kilometers, and it is necessary to clean it up. The malfunction of the throttle could be indicated by illuminated EPC warning light. This is usually the case with modern Volkswagen Group vehicles. Vehicles not equipped with the EPC warning light indicate issues with the throttle by illuminated check engine symbol.

Symptoms of the throttle malfunction could vary from poor idle, decreased engine power, poor mileage, bad acceleration, and so on. The effective way to increase the throttle's lifespan is through regular maintenance and cleaning.