Completeness (statistics)

Examples

Bernoulli model

The Bernoulli model admits a complete statistic. Let X be a random sample of size n such that each X_i has the same Bernoulli distribution with parameter p. Let T be the number of 1s observed in the sample, i.e. ${\displaystyle T=\sum _{i=1}^n{X}_i}$. T is a statistic of X which has a binomial distribution with parameters (n,p). If the parameter space for p is (0,1), then T is a complete statistic. To see this, note that

${\displaystyle {\mathrm{E}}_p(g(T))=\sum _{t=0}^{n}g(t)(\genfrac{}{}{0ex}{}{n}{t})p^t(1-p{)}^{n-t}=(1-p{)}^n\sum _{t=0}^{n}g(t)(\genfrac{}{}{0ex}{}{n}{t}){\left(\frac{p}{1-p}\right)}^t.}$

Observe also that neither p nor 1 − p can be 0. Hence ${\displaystyle E_p(g(T))=0}$ if and only if:

${\displaystyle \sum _{t=0}^{n}g(t)(\genfrac{}{}{0ex}{}{n}{t}){\left(\frac{p}{1-p}\right)}^t=0.}$

On denoting p/(1 − p) by r, one gets:

${\displaystyle \sum _{t=0}^{n}g(t)(\genfrac{}{}{0ex}{}{n}{t})r^t=0.}$

First, observe that the range of r is the positive reals. Also, E(g(T)) is a polynomial in r and, therefore, can only be identical to 0 if all coefficients are 0, that is, g(t) = 0 for all t.

It is important to notice that the result that all coefficients must be 0 was obtained because of the range of r. Had the parameter space been finite and with a number of elements less than or equal to n, it might be possible to solve the linear equations in g(t) obtained by substituting the values of r and get solutions different from 0. For example, if n = 1 and the parameter space is {0.5}, a single observation and a single parameter value, T is not complete. Observe that, with the definition:

${\displaystyle g(t)=2(t-0.5),}$

then, E(g(T)) = 0 although g(t) is not 0 for t = 0 nor for t = 1.

Gaussian model with fixed variance

This example will show that, in a sample X₁, X₂ of size 2 from a normal distribution with known variance, the statistic X₁ + X₂ is complete and sufficient. Suppose X₁, X₂ are independent, identically distributed random variables, normally distributed with expectation θ and variance 1. The sum

${\displaystyle s((X_1,X_2))=X_1+X_2}$

is a complete statistic for θ.

To show this, it is sufficient to demonstrate that there is no non-zero function ${\displaystyle g}$ such that the expectation of

${\displaystyle g(s(X_1,X_2))=g(X_1+X_2)}$

remains zero regardless of the value of θ.

That fact may be seen as follows. The probability distribution of X₁ + X₂ is normal with expectation 2θ and variance 2. Its probability density function in ${\displaystyle x}$ is therefore proportional to

${\displaystyle \exp \left(-(x-2\theta {)}^2/4\right).}$

The expectation of g above would therefore be a constant times

${\displaystyle {\int }_{-\mathrm{\infty }}^{\mathrm{\infty }}g(x)\exp \left(-(x-2\theta {)}^2/4\right)dx.}$

A bit of algebra reduces this to

${\displaystyle k(\theta ){\int }_{-\mathrm{\infty }}^{\mathrm{\infty }}h(x)e^{x\theta }dx,}$

where k(θ) is nowhere zero and

${\displaystyle h(x)=g(x)e^{-x^2/4}.}$

As a function of θ this is a two-sided Laplace transform of h, and cannot be identically zero unless h is zero almost everywhere. The exponential is not zero, so this can only happen if g is zero almost everywhere.

By contrast, the statistic $(X_1,X_2)$ is sufficient but not complete. It admits a non-zero unbiased estimator of zero, namely $X_1-X_2$.

Sufficiency does not imply completeness

Most parametric models have a sufficient statistic which is not complete. This is important because the Lehmann–Scheffé theorem cannot be applied to such models. Galili and Meilijson 2016 propose the following didactic example.

Consider ${\displaystyle n}$ independent samples from the uniform distribution:

${\displaystyle X_i\sim U((1-k)\theta ,(1+k)\theta )0<k<1}$

${\displaystyle k}$ is a known design parameter. This model is a scale family (a specific case of a location-scale family) model: scaling the samples by a multiplier ${\displaystyle c}$ multiplies the parameter ${\displaystyle \theta }$.

Galili and Meilijson show that the minimum and maximum of the samples are together a sufficient statistic: ${\displaystyle X_{(1)},X_{(n)}}$ (using the usual notation for order statistics). Indeed, conditional on these two values, the distribution of the rest of the sample is simply uniform on the range they define: ${\displaystyle \left[X_{(1)},X_{(n)}\right]}$.

However, their ratio has a distribution which does not depend on ${\displaystyle \theta }$. This follows from the fact that this is a scale family: any change of scale impacts both variables identically. Subtracting the mean ${\displaystyle m}$ from that distribution, we obtain:

${\displaystyle \mathbb{E}\left[\frac{X_{(n)}}{X_{(1)}}\right]-m=0}$

We have thus shown that there exists a function ${\displaystyle g\left(X_{(1)},X_{(n)}\right)}$ which is not ${\displaystyle 0}$ everywhere but which has expectation ${\displaystyle 0}$. The pair is thus not complete.

Importance of completeness

The notion of completeness has many applications in statistics, particularly in the following theorems of mathematical statistics.

Lehmann–Scheffé theorem

Completeness occurs in the Lehmann–Scheffé theorem, which states that given a complete and sufficient statistic ${\displaystyle T}$, an unbiased estimator for the parameter θ of the form ${\displaystyle g(T)}$, for some measurable function ${\displaystyle g}$, is the best mean-unbiased estimator for θ. In other words, the estimator ${\displaystyle g(T)}$ has the smallest expected loss for any convex loss function; in many practical applications with the squared loss-function, it has a smaller mean squared error among any estimators with the same expected value.

There are examples where the minimal sufficient statistic is not complete and where several alternative statistics for unbiased estimation of θ exist, while some of them have lower variance than others.

See also minimum-variance unbiased estimator.

Basu's theorem

Bounded completeness occurs in Basu's theorem, which states that a statistic that is both boundedly complete and sufficient is independent of any ancillary statistic.

Bahadur's theorem

Bounded completeness also occurs in Bahadur's theorem. In the case where there exists at least one minimal sufficient statistic, a statistic which is sufficient and boundedly complete, is necessarily minimal sufficient.